MAGRES EAM580R-SC - Analog | Absolute encoders

Encoder single- or multiturn / Analog
E1 compliant design
High protection up to IP 67
High resistance to shock and vibrations
Protection against corrosion CX (C5-M)
Wire cross section 0.5 mm²
Teach input for adjustment of measuring range
Applicable up to PLd (ISO 13849)

available on request

Technical data

show all

Technical data - electrical ratings

Voltage supply

8...30 VDC
14...30 VDC

Reverse polarity protection

Consumption typ.

20 mA (24 VDC, w/o load)

Initializing time

≤ 170 ms after power on

Response time

< 1 ms

Interface

Analog 0...10 V / 0.5...4.5 V / 4...20 mA / Resolution: 12 bit

Function

Multiturn
Singleturn

Teach range

5°...359.9° (singleturn)
5°...32767 turns (multiturn)

Absolute accuracy

±0.15 ° (+20 ±15 °C)
±0.25 ° (-40...+85 °C) sensor

Accuracy analog output

±0.5 % of whole measuring range
(-40...+85 °C)

Sensing method

Magnetic

Interference immunity

EN 61000-6-2
ISO 11452-2:2004* / -5:2002*
ISO 7637-2:2004*
ISO 10605:2008 + Amd 1:2014 (CD ±8 kV / AD ±15 kV)
* Severity level according to ECE R10 (Rev. 4)

Emitted interference

EN 61000-6-4
CISPR 25:2008 (30...1000 MHz)
ISO 7637-2:2004*
* Severity level according to ECE R10 (Rev. 4)

MTTF_d (ISO 13849)

High (>100 years)
Use in safety functions exclusively based on Application Note and MTTFd reliability prediction (request separately).

Programmable parameters

Measuring range teachable

Diagnostic function

DATAVALID

Factory setting

360° and 10 revolutions (other on request)

Approval

UL approval / E217823

Technical data - mechanical design

Size (flange)

ø58 mm

Shaft type

ø10 x 20 mm, solid shaft with flat

Flange

Clamping flange

Protection EN 60529

IP 67 (with shaft seal)

Operating speed

≤6000 rpm

Starting torque

≤2.5 Ncm (+20 °C, IP 67)

Moment of inertia

15.38 gcm²

Admitted shaft load

≤40 N axial
≤80 N radial

Material

Housing: steel, powder-coated
Flange: aluminium
Shaft: stainless steel

Corrosion protection

IEC 60068-2-52 Salt mist
for ambient conditions CX (C5-M) according to ISO 12944-2

Operating temperature

-40...+85 °C (see general information)

Relative humidity

95 %

Resistance

EN 60068-2-6
Vibration 30 g, 10-2000 Hz
EN 60068-2-27
Shock 500 g, 1 ms

Weight approx.

250 g

Connection

Flange connector M12, 5-pin
Cable 2 m

Downloads

show all

Data sheet

Data sheet – EAM580R-SC - Analog
- ZH (pdf | 1 MB)
Data sheet – EAM580R-SC - Analog
- FR (pdf | 947 KB)
Data sheet – EAM580R-SC - Analog
- DE (pdf | 918 KB)
Data sheet – EAM580R-SC - Analog
- EN (pdf | 945 KB)

Quickstart

EAM580R - analog
- DE/EN/FR/IT/ES/RU (pdf | 860 KB)

Brochures / Catalogs

Brochure – Magnetic absolute encoders EAM580 / EAM360
- DE (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- EN (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- FR (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- IT (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- ES (pdf | 1 MB)
Brochure – Magnetic absolute encoders EAM580 / EAM360
- ZH (pdf | 1 MB)

Declaration of conformity

DoC / CoC - EAM580 / EAM580R
- EN/DE/BG/CZ/DK/ES/FI/FR/GR/HU/IT/LT/LV/NL/NO/PL/PT/RO/SK/SI (pdf | 281 KB)

CAD

EAM580 / EAM580R: Solid shaft ø10 mm, cable radial, clamping flange, IP67
- (zip | 200 KB)
EAM580 / EAM580R: Solid shaft ø10 mm, M12 radial, clamping flange, IP67
- (zip | 190 KB)

Accessories

show all

Mounting accessories

	Double loops coupling (D1=10 / D2=10) For encoder with solid shaft Article no.: 11101781	Thermally and electrically isolated Absorbing shocks and vibration Excellent compensation of radial, lateral and angular misalignments Medium torsional stiffness Low restoring forces Maintenance-free
	Bellows coupling (D1=06 / D2=10) For encoder with solid shaft Article no.: 11050507	Backlash-free angle-synchronous transmission Optimum compensation of misalignments Very high torsional spring stiffness Small restoring force Vibration damping Stainless steel bellows
	Coupling CPS25 (L=19, D1=10 / D2=10) For encoder with solid shaft Article no.: 11065923	Precision coupling Torsionally stiff coupling with low installation depth Pluggable Electrically insulating center disk Suitable for very high speeds
	Coupling CPS25 (L=19, D1=10 / D2=06) For encoder with solid shaft Article no.: 11065922	Precision coupling Torsionally stiff coupling with low installation depth Pluggable Electrically insulating center disk Suitable for very high speeds
	Spring washer coupling (D1=6 / D2=10) For encoder with solid shaft Article no.: 10141132	Backlash-free and angle-synchronous transmission of rotary movements Plug-in version Electric isolated Suitable for very high speeds Good compensation of all misalignments
	Spring washer coupling (D1=10 / D2=10) For encoder with solid shaft Article no.: 10141133	Backlash-free and angle-synchronous transmission of rotary movements Plug-in version Electric isolated Suitable for very high speeds Good compensation of all misalignments
	Coupling CPS37 (L=24, D1=10 / D2=06) For encoder with solid shaft Article no.: 11069337	Precision coupling Torsionally stiff coupling with low installation depth Pluggable Electrically insulating center disk Suitable for very high speeds
	Coupling CPS37 (L=24, D1=10 / D2=10) For encoder with solid shaft Article no.: 11069340	Precision coupling Torsionally stiff coupling with low installation depth Pluggable Electrically insulating center disk Suitable for very high speeds
	Bellows coupling (D1=10 / D2=10) For encoder with solid shaft Article no.: 11053277	Backlash-free angle-synchronous transmission Optimum compensation of misalignments Very high torsional spring stiffness Small restoring force Vibration damping Stainless steel bellows
	Spring encoder arm Article no.: 11101893	Tether arm for Ø58 mm with clamping flange Optimal for use encoders with measuring wheel Virtually any contact pressure adjustable Versatile mounting options
	Mounting adaptor For encoders with clamping flange Article no.: 10125051	Glass-fiber reinforced plastic Excellent resistance against temperature and chemicals Electrically isolated encoder mount

Connectors and cables

	Female connector M12, 5-pin, straight, without cable Article no.: 10153968	Female connector M12, 5-pin, straight
	Cable with male/female M12, 5-pin, straight, A-coded, 500 cm Article no.: 11144306	M12, male, A-coded; 5-poles; PUR, 500 cm; M12, female, A-coded; 5-poles Dragchain capable; Head A: IP65, IP67; Head B: IP65, IP67 Suiteable for CANopen and DeviceNet Halogen free

Measuring wheels

	MR752.10A Small measuring wheel Article no.: 11011440	Circumference 30.48 cm Surface profile: Smooth Surface material: Polyurethan Bore ø10 mm
	MR241.10D Small measuring wheel Article no.: 11033281	Circumference 20 cm Surface profile: Smooth Surface material: Hytrel TPE-E Bore ø10 mm
	MR261.10A Small measuring wheel Article no.: 11033290	Circumference 20 cm Surface profile: Knopped rubber Surface material: Nitrile NBR Bore ø10 mm
	MR291.10D Small measuring wheel Article no.: 11033300	Circumference 20 cm Surface profile: Knurled Surface material: Hytrel TPE-E Bore ø10 mm
	MR512.10A Large measuring wheel Article no.: 11033308	Circumference 50 cm Surface profile: Cross-knurled Surface material: Aluminium Bore ø10 mm
	MR552.10A Large measuring wheel Article no.: 11033323	Circumference 50 cm Surface profile: Smooth Surface material: Polyurethan Bore ø10 mm
	MR562.10A Large measuring wheel Article no.: 11033329	Circumference 50 cm Surface profile: Knopped rubber Surface material: Nitrile NBR Bore ø10 mm
	MR542.10D Large measuring wheel Article no.: 11038480	Circumference 50 cm Surface profile: Smooth Surface material: Hytrel TPE-E Bore ø10 mm
	MR592.10D Large measuring wheel Article no.: 11038481	Circumference 50 cm Surface profile: Knurled Surface material: Hytrel TPE-E Bore ø10 mm